 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| FEATURES * -55C to +125C operation * Up to 60 dB attenuation at 500 kHz. * Compliant to MIL-STD-461C, CE03 * Compatible with MIL-STD-704E DC power bus EMI INPUT FILTERS 28 & 270 VOLT INPUT FMD/FME EMI FILTER 0.7 TO 15 AMP MODELS INPUT VOLTAGE AND CURRENT Input (V) 28 28 270 270 Current ( A) 7.0 15.0 0.7 1.5 Size (max.): Case U2, FME all models; Case U1, FMD28-461SL and FMD270-461SL 3.005 x 1.505 x 0.400 inches (76.33 x 38.23 x 11.16 mm) [FME models, shown in Case U2 (flanged, short leads). Also available: Flanged - leads bent down (case V); Tabbed - leads bent up (case W), short leads (case Y), and leads bent down (case Z).See Section B8, cases U2, V, W, Y, and Z for dimensions and options.] Case J4, FMD28-461 2.720 x 1.350 x 0.505 inches (69.09 x 34.29 x 12.83 mm) See Section B8, cases J4, U1, U2, V, W, Y, and Z for dimensions. Weight: 77 grams typical cases U1, U2, V, W, Y, and Z; 55 grams typical case J4 Screening: Standard, ES, or 883 (Class H). See Section C2 for screening options, see Section A5 for ordering information. DESCRIPTION The FMD SeriesTM and FME SeriesTM EMI filters are specifically designed to reduce the reflected input ripple current of Interpoint's high frequency DC/DC converters. FMD/FME filters minimize electromagnetic interference (EMI) for the MHE, MHL, MLP, MRH, MTO, MHF, MHF+, MHV, MHD, MTR, MFL, MHP, and MFLHP Series. These filters are intended for use in 28 or 270 volt applications which must meet MIL-STD-461C, CE03 levels of conducted emissions. One filter can be used with multiple converters up to the rated output current of the filter. best connection, mount the filter's and converter's baseplates on or above a small ground plane. See Figure 5. TRANSIENTS The transients listed below will not damage the filter but will be passed on to the converter: * All filters: 600 volts (50 ohm source impedance) for up to 10 s. * 28 volt filter: 100 volts (0.5 ohm source impedance) for up to 100 ms. * 270 volt filter: 500 volts (independent of source impedance) for up to 100 ms. INPUT RIPPLE AND EMI Switching DC/DC converters naturally generate two noise components on the power input line: differential noise and common mode noise. Input ripple current refers to both of these components. Differential noise occurs between the positive input and input common. Most Interpoint converters have an input filter that reduces differential noise which is sufficient for many applications. Common mode noise occurs across stray capacitances between the converter's power train components and the baseplate (bottom of the package) of the converter. Where low noise currents are required to meet CE03 of MIL-STD461, a power line filter is needed. The FMD/FME Series of EMI power line filters reduces the common mode and differential noise generated by the converters. FMD/FME-461 filters reduce input ripple current by as much as 60 dB at 500 kHz and 55 dB at 1 MHz when used in conjunction with Interpoint's DC/DC converters. See Figures 8 and 9. Place the filter as close as possible to the converter for optimum performance. The baseplates of the filter and the converter should be connected with the shortest and widest possible conductors. For the OPERATION OVER TEMPERATURE All FMD/FME-461 Series filters are rated for full power operation from -55C to +125C case temperature. Current is derated linearly to zero at +135C case temperature. INSERTION LOSS The maximum dc insertion loss at full load and nominal input voltage represents a power loss of less than 4%. PACKAGING FMD/FME-461 filters are sealed in metal hermetic side-leaded packages. See Section B8, cases U1, U2, V, W, Y, and Z. Additionally the FMD28-461 filter is available in a metal hermetic down-leaded package (see Section B8, case J4). LAYOUT REQUIREMENTS The case of the filter must be connected to the case of the converter through a low impedance connection to minimize EMI. B3-7 FMD/FME EMI FILTER 0.7 TO 15 AMP ABSOLUTE MAXIMUM RATINGS EMI INPUT FILTERS RECOMMENDED OPERATING CONDITIONS Input Voltage Range * 0 to 40 VDC continuous for 28 V models * 0 TO 400 VDC continuous for 270 V models Case Operating Temperature (Tc) * -55C to +125C full power * -55C to +135C absolute Derating Input/Output Current * Linearly from 100% at 125C to 0% at 135 C Input Voltage * 0 to 40 VDC continuous for 28 V models * 0 to 400 VDC continuous for 270 V models Lead Soldering Temperature (10 sec per lead) * 300C Storage Temperature Range (Case) * -65C to +150C Isolation * 100 megohm minimum at 500 V, any pin to case (except FMD downleaded case case pin) Electrical Characteristics: 25C Tc, nominal Vin, unless otherwise specified. FMD28-461 PARAMETER INPUT VOLTAGE NOISE REJECTION DC RESISTANCE (RDC) CAPACITANCE OUTPUT VOLTAGE OUTPUT CURRENT POWER DISSIPATION CONDITION CONTINUOUS TRANSIENT 100 ms1 500 kHz 1 MHz MAX. CURRENT Tc=25C Tc=125C ANY PIN TO CASE STEADY STATE STEADY STATE MAX. CURRENT Tc=25C Tc=125C -- -- -- -- -- -- 7 6.0 7.4 -- -- -- MIN 0 -100 50 45 -- -- -- TYP 28 -- 60 55 -- -- 20,000 MAX 40 100 -- -- 0.12 0.15 -- MIN 0 -500 50 45 -- -- -- FMD270-461 TYP 270 -- 60 55 -- -- 30,000 MAX 400 500 -- -- 5.0 6.3 -- MIN 0 -100 30 40 -- -- -- FME28-461 TYP 28 -- 40 50 -- -- 60,000 MAX 40 100 -- -- 0.07 0.07 -- 0 -500 40 45 -- -- -- FME270-461 MIN TYP 270 -- 50 55 -- -- 60,000 MAX 400 500 -- -- 2.0 3.2 -- UNITS VDC V dB pF VDC VOUT = VIN - IIN(RDC) -- -- -- 0.7 2.5 3.1 -- -- -- -- -- -- 15 15.75 15.75 -- -- -- -- -- -- 1.5 4.5 7.2 A W Note 1. 28 V models = 0.5 source impedance, 270 V models = independent of source impedance. B3-8 EMI INPUT FILTERS 100 H Positive Input 0.55 H 100 H 1.25 H FMD/FME EMI FILTER 0.7 TO 15 AMP 1.25 H Positive Output 6F 50 V 6F 50 V 6F 50 V Input Common Output Common FME28-461 FIGURE 1: FME28-461 SCHEMATIC - TYPICAL VALUES 0.015 F 500 V 1.8 mH Positive Input 37 H 1.8 mH 37 H 37 H Positive Output 1.3 0.015 F 0.68 F 0.68 F Input Common Output Common 0.015 F x2 x2 FME270-461 FIGURE 2: FME270-461 SCHEMATIC - TYPICAL VALUES B3-9 FMD/FME EMI FILTER 0.7 TO 15 AMP 135 H Positive Input EMI INPUT FILTERS 135 H 4.1 H 4.1 H Positive Output 1.3 0.1 F 50 V 6F 50 V 10 F 50 V 4.1 H Input Common 0.015 F 500V 0.01 F 500 V Output Common FMD28-461 FIGURE 3: FMD28-461 SCHEMATIC - TYPICAL VALUES 844 H Positive Input 844 H 18.5 H 18.5 H Positive Output 1.3 0.015 F 0.68 F 0.68 F Input Common Output Common 0.015 F FMD270-461 FIGURE 4: FMD270-461 SCHEMATIC - TYPICAL VALUES EMI FILTER +Vin +Vout Case Output Input Common Common DC/DC CONVERTER +Vin +Vout RL Case Output Input Common Common Chassis ground Multiple units allowed up to rated output current of filter RL The case ground connection between the filter and the converter should be as low an impedance as possible to minimize EMI. Direct contact of baseplate to chassis ground provides the lowest impedance. FIGURE 5: CONNECTION DIAGRAM B3-10 EMI INPUT FILTERS PIN OUT SIDE-LEADED MODELS FMD28-461SL, FMD270-461SL, FME28-461, and FME270-461 Pin1 1, 2, 3 4, 5, 6 7, 8, 9 10, 11, 12 -- Designation Positive Input Input Common Output Common Positive Output Case Ground2 FMD/FME EMI FILTER 0.7 TO 15 AMP Angled corner and cover marking indicate pin one for cases U1, U2, and V. Cover marking indicates pin one for cases W, Y and Z. 1 2 3 4 5 6 Outline shown is case U2, pin out is the same for all side-leaded cases. Also available: flanged - leads bent down (case V); tabbed - leads bent up (case W), short leads (case Y), and leads bent down (case Z). See Section B8, cases U1, U2, V, W, Y, and Z for dimensions. TOP VIEW All FME models, FMD28-461SL, and FMD270-461SL (Pin side, marked side) 12 11 10 9 8 7 Notes 1. All pins must be connected. 2. The baseplate is the only case ground connection and should directly contact chassis ground. FIGURE 6: PIN OUT SIDE-LEADED MODELS FMD28-461 Pin 1 2 3 4 5 Designation Positive Input Positive Output Output Common Case Ground1 Input Common PIN OUT DOWN-LEADED MODEL Squared corner and dot on top of package indicate pin one. 1 2 BOTTOM VIEW FMD28-461 5 4 3 Note 1. Although down-leaded packages can be connected to chassis ground with the case ground lead, direct contact of the base plate to chassis improves EMI performance. See Section B8, case J4, for dimensions. FIGURE 7: PIN OUT FMD28-461 DSCC NUMBERS DSCC DRAWING (5915) 95004-01HXC 95004-01HTC 95004-01HUC 95004-01HYC 95004-01HZC 95009-01HXC IN PROCESS IN PROCESS IN PROCESS IN PROCESS FME SERIES SIMILAR PART FME28-461/883 FME28-461W/883 FME28-461V/883 FME28-461Y/883 FME28-461Z/883 FME270-461/883 FME270-461W/883 FME270-461V/883 FME270-461Y/883 FME270-461Z/883 MODEL NUMBERING KEY FME Base Model Input Voltage MIL-STD-461 Reference Case/Lead Option* Screening (Standard screening has no designator in this position.) 28 - 461 V / 883 *Case/Lead Option: See section B8, cases J4, U1, U2, V, W, Y, and Z for drawings and dimensions, see Section A5 for ordering information. FME models: Case U2 has no designator in the case/lead option position. To designate a case option add the case letter to the model number - FME28-461V. FMD models: Case J4 (down-leaded) has no designator in the case/leadoption position. To designate case U1 (side-leaded) for the FMD place "SL" in the case/lead option position - FMD28-461SL. The 270 volt FMD is only available in the side-leaded case - FMD270-461SL. For exact specifications for a DSCC product, refer to the DSCC drawing. Contact your Interpoint representative for status on the FME DSCC releases. See Section A3, "SMD/DSCC Lists", for more information. B3-11 FMD/FME EMI FILTER 0.7 TO 15 AMP 90 80 EMISSION LEVEL (dB A 70 60 50 40 30 20 10 0 .015 0.1 1 FREQUENCY (MHz) 10 EMI INPUT FILTERS 90 80 EMISSION LEVEL (dB A) 70 60 50 40 30 20 10 0 50 .015 0.1 1 FREQUENCY (MHz) 10 50 Typical Performance Curves: 25C Tc , nominal Vin, unless otherwise specified. CE 03 NARROWBAND CE LI 03 M IT LI NARROWBAND M IT Three paralleled and synchronized MFL2815D converters without filtering. Three paralleled and synchronized MFL2815D converters with an FME28-461. FIGURE 8 FIGURE 9 1.0 IMPEDANCE (OHMS) 1.0 IMPEDANCE (OHMS) 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.1 1.0 10 FREQUENCY (kHz) 100 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.1 1.0 10 FREQUENCY (kHz) 100 DC BIAS: 1 AMP DC BIAS: 10 AMP FME28-461 OUTPUT IMPEDANCE FME28-461 OUTPUT IMPEDANCE FIGURE 10 FIGURE 11 B3-12 22021-001-DTS Rev B (CaseJ4) DQ# 4002 All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. FMD Series and FME Series are trademarks of Interpoint. Copyright (c) 1992 - 1999 Interpoint. All rights reserved. CASE U CASES Angled corner indicates pin one 1.505 max (38.23) CASE U TOP VIEW (PIN SIDE) See Figures 55 and 56 for dimensions 3.005 (76.33) max. Note: Pins are shown for Case U1. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold compression glass seal Case dimensions in inches (mm) Tolerance 0.005 (0.13) for three decimal places 0.01 (0.2) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300C for 10 seconds per pin. FIGURE 54: CASE U MAXIMUM DIMENSIONS B8-36 CASE U CASES PIN-SIDE VIEW CASE U2* (Flanged case, short leads) MOR Series and FME EMI Filters: Screening - Standard, ES, or 883 Also available in V, W, Y, and Z cases (Figures 57 - 60) Pin Length 0.30 0.05 (7.6 1.3) Seam Seal 0.128 dia (3.25). 0.040 dia (1.02) Angled corner indicates pin one. 1.380 (35.05) 1.250 (31.75) 1.050 (26.67) 0.850 (21.59) 0.650 (16.51) 0.450 (11.43) 0.250 (6.35) 0.120 (3.05) 0.000 0.000 0.120 (3.05) 0.250 (6.35) 1 2 3 4 5 6 12 11 10 9 8 7 2.750 (69.85) 2.880 (73.15) 0.400 (10.16) max. 0.220 (5.59 *No designator is required in the case option position, see Section A5, Ordering Information. FIGURE 56: CASE U2 B8-38 0.050 (1.27) 0.000 CASES PIN-SIDE VIEW CASE V* Flanged case, down leaded) MOR Series and FME EMI Filters: Screening - Standard, ES, or 883 Also available in U2, W, Y, and Z cases (Figures 56 and 58 - 60) *Requires case option designator added to model number: MOR2805SV See Section A5, Ordering Information. Angled corner indicates pin one. CASE V Maximum dimensions: 3.005 x 1.505 (76.33 x 38.23 mm) 3.45 (87.6) Reference (lead center to lead center) 0.128 dia (3.25) 0.040 dia (1.02) 1 2 3 4 5 6 12 11 10 9 8 7 1.380 (35.05) 1.250 (31.75) 1.050 (26.67) 0.850 (21.59) 0.650 (16.51) 0.450 (11.43) 0.250 (6.35) 0.120 (3.05) 0.000 0.225 (5.72 0.000 0.120 (3.05) 0.250 (6.35) 2.750 (69.85) 2.880 (73.15) 0.400 (10.16) max 0.220 (5.59) 0.050 (1.27) 0.000 Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold compression glass seal Case dimensions in inches (mm) Tolerance 0.005 (0.13) for three decimal places 0.01 (0.2) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300C for 10 seconds per pin. FIGURE 57: CASE V B8-39 0.250 (6.35) .050 (1.27) CASE W CASES PIN-SIDE VIEW CASE W* (Tabbed case, up-leaded) MOR Series and FME EMI Filters: Screening - Standard, ES, or 883 Also available in U2, V, Y, and Z cases (Figures 56, 57, 59 and 60) *Requires case option designator added to model number: MOR2805SW See Section A5, Ordering Information. 0.250 (6.35) Typ. 0.140 dia (3.56) 0.250 (6.35) Typ. 0.040 dia (1.02) 1.750 (44.45) 1.625 (41.28) 1.375 (34.93) 1.175 (29.85 0.975 (24.77) 0.775 (19.69) 0.575 (14.61) 0.375 (9.53) 0.125 (3.18) 0.000 1 2 3 4 5 6 12 11 10 9 8 7 2.000 (50.80) 0.84 0.05 (21.3 1.3) 0.400 (10.16) max. 0.220 (5.59) 2.125 (53.98) 1.750 (44.45) 1.450 (36.83) 0.300 (7.62) Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold compression glass seal Case dimensions in inches (mm) Tolerance 0.005 (0.13) for three decimal places 0.01 (0.2) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300C for 10 seconds per pin. 0.375 (9.53) Lead Detail 0.84 0.05 (21.3 1.3) 0.400 (10.16) max. 0.220 (5.59) 0.000 0.150 (3.81) 2.80 (71.1) Reference (lead center to lead center) FIGURE 58: CASE W B8-40 0.050 (1.27) 0.000 0.000 CASES PIN-SIDE VIEW CASE Y* (Tabbed case, straight leads) MOR Series and FME EMI Filters: Screening - Standard, ES, or 883 Also available in U2, V, W, and Z casee (Figures 56, 57, 58 and 60) 0.250 (6.35) Typ. 1.750 (44.45) 1.625 (41.28) 1.375 (34.93) 1.175 (29.85 0.975 (24.77) 0.775 (19.69) 0.575 (14.61) 0.375 (9.53) 0.125 (3.18) 0.000 1 2 3 4 5 6 0.250 (6.35) Typ. 0.040 dia (1.02) 0.140 dia (3.56) CASE Y Bathtub Seam Seal 12 11 10 9 8 7 2.000 (50.80) 0.220 (5.59) *Requires case option designator added to model number: MOR2805SY See Section A5, Ordering Information. Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold compression glass seal Case dimensions in inches (mm) Tolerance 0.005 (0.13) for three decimal places 0.01 (0.2) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300C for 10 seconds per pin. 0.400 (10.16) max. 0.220 (5.59) 0.000 Lead Detail 0.30 0.05 (7.6 1.3) 3.10 (78.7) Reference FIGURE 59: CASE Y 0.400 (10.16) max. 2.125 (53.98) 1.750 (44.45) 1.450 (36.83) 0.300 (7.62) 0.375 (9.53) 0.050 (1.27) 0.000 Pin Length 0.30 0.05 (7.6 1.3) 0.000 B8-41 CASE Z CASES PIN-SIDE VIEW CASE Z* (Tabbed case, down-leaded) MOR Series and FME EMI Filters: Screening - Standard, ES, or 883 Also available in U2, V, Y, and W cases (Figures 56, 57, 58 and 59) *Requires case option designator added to model number: MOR2805SZ See Section A5, Ordering Information. 0.250 (6.35) Typ. 1.750 (44.45) 1.625 (41.28) 1.375 (34.93) 1.175 (29.85 0.975 (24.77) 0.775 (19.69) 0.575 (14.61) 0.375 (9.53) 0.125 (3.18) 0.000 1 2 3 4 5 6 0.250 (6.35) Typ. 0.040 dia (1.02) 0.140 dia (3.56) 12 11 10 9 8 7 2.000 (50.80) 0.400 (10.16) max. 0.220 (5.59) 2.125 (53.98) 1.750 (44.45) 1.450 (36.83) 0.300 (7.62) 0.375 (9.53) Materials Header Cold Rolled Steel/Nickel/Gold Cover Kovar/Nickel Pins #52 alloy/Gold compression glass seal Case dimensions in inches (mm) Tolerance 0.005 (0.13) for three decimal places 0.01 (0.2) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300C for 10 seconds per pin. Lead Detail 0.150 (3.81) 0.400 (10.16) max. 0.220 (5.59) 0.000 0.36 0.05 (9.10.13) 2.80 (71.1) Reference (lead center to lead center) FIGURE 60: CASE Z B8-42 0.050 (1.27) 0.000 0.36 0.05 (9.10.13) 0.000 CASES TOP VIEW CASE U1 MFL Series and MHP Series: Screening - Standard, ES or 883 MFLHP Series, FMD270 EMI Filter, and FMD28-461SL EMI Filters: Screening - Standard or ES SMFL, SMFLHP, SMHP, and SSP Series; SFCS, and SFME EMI Filters: Screening - Standard, Class H or K HUM70 Module and LCM Module: Screening - Standard or ES Angled corner indicates pin one. 1.505 (38.23) max. 1.380 (35.05) 1.250 (31.75) 1.050 (26.67) 0.850 (21.59) 0.650 (16.51) 0.450 (11.43) 0.250 (6.35) 0.120 (3.05) 0.000 0.400 (10.16) max. CASE U Seam Seal 0.23 (5.8) Lead Length 0.128 dia (3.25). 0.040 dia (1.02) 1 2 3 4 5 6 12 11 10 9 8 7 0.120 (3.05) 0.250 (6.35) 2.750 (69.85) 2.880 (73.15) 3.005 (76.33) max. 0.220 (5.59 FIGURE 55: CASE U1 0.050 (1.27) 0.000 0.000 B8-37 CASE J CASES Dot on top of case indicates pin one CASE J BOTTOM VIEW See Figures 36 - 40 for pin configuration 1.350 max (34.29) 2.720 max (69.09) Flange Thickness: Cases J1 and J5 Case J2 Cases J3 and J4 0.060 (1.52) 0.073 (1.85) max 0.067 +0.005/-0.007 (1.70 +0.13/-0.8) Materials Header Case J1 Cold Rolled Steel/Nickel/Gold Cases J2 - J5 Cold Rolled Steel/Nickel/Tin Cover Case J1 Kovar/Nickel Case J2 - J5 Cold Rolled Steel/Nickel/Tin Pins #52 alloy (all cases) Case J1 MHV Series Triple - compression glass seal MTR Series Triple - ceramic seal Cases J2 - J5 compression glass seal Case dimensions in inches (mm) Tolerance 0.005 (0.13) for three decimal places 0.01 (0.2) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300C for 10 seconds per pin. FIGURE 35: CASE J MAXIMUM DIMENSIONS Note: Although every effort has been made to render the case drawings at actual size, variations in the printing process may cause some distortion. Please refer to the numerical dimensions for accuracy. B8-22 CASES BOTTOM VIEW CASE J4 (Rev B) Flanged cases: Designator required in Case Option position of model number. FMD28-461 EMI Filter (down-leaded): Screening - Standard or ES Solder Seal 1.173 (29.79 0.040 dia. (1.02) 0.673 (17.09) CASE J Squared corner and dot on top of case indicate pin one. 1 2 0.162 dia (4.11) Solder Tip-off 0.173 (4.39) 0.000 0.170 (4.32) 1.370 (34.80) 0.25 (6.4) 0.505 max (12.83) 1.770 (44.96) 0.210 (5.33) 0.000 0.000 2.150 (54.61) 5 4 3 FIGURE 39: CASE J4 B8-25 QA SCREENING 125C PRODUCTS 125C PRODUCTS TEST (125C Products) PRE-CAP INSPECTION Method 2017, 2032 TEMPERATURE CYCLE (10 times) Method 1010, Cond. C, -65C to 150C Method 1010, Cond. B, -55C to 125C CONSTANT ACCELERATION Method 2001, 3000 g Method 2001, 500 g BURN-IN Method 1015, 160 hours at 125C 96 hours at 125C case (typical) FINAL ELECTRICAL TEST MIL-PRF-38534, Group A Subgroups 1 through 6: -55C, +25C, +125C Subgroups 1 and 4: +25C case HERMETICITY TESTING Fine Leak, Method 1014, Cond. A Gross Leak, Method 1014, Cond. C Gross Leak, Dip (1 x 10-3) FINAL VISUAL INSPECTION Method 2009 STANDARD /ES /883 (Class H)* yes yes yes no no no yes yes no no no no yes yes no no no no yes yes no no yes no yes yes no no no yes yes yes no yes yes no yes yes yes Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534. *883 products are built with element evaluated components and are 100% tested and guaranteed over the full military temperature range of -55C to +125C. Applies to the following products MOR Series MHD Series MFLHP Series MHV Series MFL Series MHF+ Series MHP Series MHF Series** MTR Series MGA Series MQO Series** MSA Series MGH Series MCH Series FM-704A EMI Filter FMD**/FME EMI Filter FMC EMI Filter FMH EMI Filter FMGA EMI Filter FMSA EMI Filter HUM Modules** LCM Modules** LIM Modules **MFLHP Series, MQO Series, MHF Series, FMD EMI Filters, Hum Modules, and LCM Modules do not offer `883" screening. C2-10 |
Price & Availability of FME28-461W
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |